狼人色国产在线视频

  • <strike id="ahk9z"></strike>
  • <th id="ahk9z"></th>
    <th id="ahk9z"></th>
      1. <em id="ahk9z"></em> <nav id="ahk9z"><sub id="ahk9z"></sub></nav>

        <label id="ahk9z"><object id="ahk9z"><menuitem id="ahk9z"></menuitem></object></label>

        PRODUCTS
        HOME>PRODUCTS>CT88KA CNC Conversion of Steam Die Forging Hammer

        PRODUCT

        TECHNOLOGY

        APPLICATION

        VIDEO

        DOCUMENTS


        Description:
        Its appearance is same as CT88K PLC fully hydraulic die forging hammer.

        Its driving system is fully hydraulic driving system designed and made by CFM, fixed on columns with elasticity anti-vibration cushion block. This system uses advanced taper valve control technology, combine cylinder transit technology, double anti-leakage and hydraulic integrating technology, simple system structure. And Key hydraulic components and seals are imported.


        Its striking system use separated hammer body structure, using old pneumatic hammer columns and anvil to modify, and columns are connected to anvil by bolts.

        Its guiding is using the steel X-shape guide rails fixed on the columns by bolts. Extending line of contacting surface of guide rails and ram crosses on the ram center, which cannot effect guide clearance due to heating, and clearance between ram and guide rails can be adjusted to be small to assure die matching. Radial X-shape wide guide structure make sure ram guiding clearance will be not changed due to heating.


        And this guide rails lubrication is automatic and exclusive, whose lubrication oil volume can be preset by operator according to machine requirement, and its level can be monitored. Once there is problem on lubrication system or level too lower, there will be alarm on touch screen and this system buzzer with alarm.


        Conversion of existing steam (air) the die forging hammer with fully hydraulic driving system is with very obvious economic effect and much cheaper than a new fully hydraulic die forging hammer. If the pump house was not considered, the hydra-pneumatic hammer may be cheaper than the fully hydraulic hammer. But in fact if the pump house and the piping system should be calculated together, the steam die hammer conversion will almost be equal. If maintaining cost is considered again, the pneumatic die hammer numerical control transformation l cost will be lower.


        Striking program is easy to input, no need skilled computer engineer, and even semi-skilled worker is OK. When hammer working, control system can check oil temperature, pressure, cleanness and position and then numerical display. Once problem, the malfunction alarm light will be on and the malfunction position and character will be on touch screen.


        Main advantages:
        1) High efficiency
        2) Energy-saving
        3) high accuracy
        4) Low noise
        5) Lower vibration
        6) Reliable quality
        7) Low running cost
        8) Wide application
        9) Ease maintenance and operation



        Main features:
        01) Program control, numerical input, simple operate;
        02) High integrated hydraulic control system, accumulator fixed directly on main valve block without any pipe connecting, improve hydraulic system efficiency and easy for maintenance
        03) Advanced taper valve control, fast response, good sealing and not easy to inner leakage;
        04) High response speed and high reliable redundancy design;
        05) Hydraulic driving system and power system assembled on top separately, no hydraulic pump station on floor;
        06) Touch screen man-machine interface and automatic malfunction diagnosis and alarm, easy for machine operation and maintenance;
        07) Safety design for inner accumulator and pipeline assembly;
        08) Swaying combine oil cylinder and thin piston rod flexible design;
        09) High and low pressure double anti-leakage design;
        10) Long ram structure can improve working accuracy;
        11) Striking energy and steps can be preset at will, no surplus striking energy can reduce striking noise and improve die life;
        12) Slow up and down in the case of releasing hydraulic system pressure to make die changing safety;
        13) Ram buffer is inner hydraulic buffer, to make sure safety and effective;


        Optional machines:
        Special designed die automatic lubrication, blank convey system, ejector and scale removing system are for customer to choose. They can be linked to hammer through program to realize die lubrication locating, timing, quantifying control, to improve its productivity and reduce labor intensity.

        Main technical parameter:

        item

        unit

        CT88KA-

        25

        CT88KA-

        50

        CT88KA-

        80

        CT88KA-

        125

        CT88KA-

        200

        CT88KA-

        250

        CT88KA-

        320

        CT88KA-

        400

        CT88KA-

        450

        Striking energy

        KJ

        25

        50

        80

        125

        200

        250

        320

        400

        450

        Max. Striking

        frequency

        Min-1

        90

        80

        70

        60

        55

        50

        45

        40

        40

        Ram weight

        Kg

        1750

        3400

        5100

        8000

        10500

        11500

        13000

        16000

        18000

        Dropping weight

        Kg

        2100

        4100

        6100

        9500

        12500

        15000

        17000

        20000

        22000

        Main motor

        power

        Kw

        55

        2X55

        2X90

        4X55

        4X90

        4X90

        4X110

        4X132

        4X132







        1.Brochure Download as PDF

        No.88 Shanghu Road, Chengdong Town, Haian, Jiangsu, P.R.China
        Tel.: 0086-513-88368808 | Fax.:0086-513-88369186 | email:cfm@cfmjs.cn

        follow us



        狼人色国产在线视频

      2. <strike id="ahk9z"></strike>
      3. <th id="ahk9z"></th>
        <th id="ahk9z"></th>
          1. <em id="ahk9z"></em> <nav id="ahk9z"><sub id="ahk9z"></sub></nav>

            <label id="ahk9z"><object id="ahk9z"><menuitem id="ahk9z"></menuitem></object></label>